This is an OEM Mitsubishi oil drain plug with gasket.

Buy this before changing your oil, to save yourself a headache later. ...

Brand new OEM EVO oil filter for your Lancer Evolution X.

This is a genuine OEM Mitsubishi oil filter, same one that comes on your EVO X ...

Battery Holder is specially designed for Mitsubishi EVO X. The holder is made of CNC machined aluminum.

These magnetic drain plugs will extend the life of your engine.

It helps to keep the excess metal particles that are created from normal engine wear from floating freely in...

The powerful cleaner spray will quickly strip away the grease and dirt, yet won't damage the air filter element.

The Boomba Racing adaptor plate that will allow mounting of EVO X 75 MM throttle body to aftermarket intake manifold with stock bolt pattern and 75 MM bore.

The Boomba Racing Adaptor is CNC machined out of billet aluminum and is available in natural aluminum, red and black anodize...

Mitsubishi Lancer EVO X CNC machined, billet aluminum oil cap. Available in red, black or natural finish. It is designed to easily replace the original oil cap.

Cosworth Performance Air Filters are constructed from a proprietary synthetic, non-woven single layer, pleated polyester filter media that requires no oiling.

Engine bearings are one of the most vital components within an engine and are often overlooked when considering high performance upgrades.

Improve throttle response and Clean up shifting in your Evolution X. Decreases Motor and transmission movement which in turn improves shifting and drive...

Don't let a flimsy paper filter get between you and true performance.The PERRIN Performance™ dual stage, "Open Cell" foam, drop-in PanelFilter is the answer. A stealthy approach to higher air flow.

K&N drop in flat panel filters with mesh covering are replacements for your stock restrictive air filter.

TECH TIP: Very easy installation. Takes less then 10 minutes and can be done in your ...

The Mishimoto EVO racing thermostat will promote greater cooling efficiency throughout your engine.

The Mishimoto racing thermostat will significantly lower high engine temperature produced by modified and upgraded turbo applications.

Once the engine is fully warme...

Boomba Racing has developed a special high temperature insulating gasket which replaces stock intake gasket.

The Cosworth Oil Filler Cap is machined from solid aluminum with the traditional Cosworth "three prong" ergonomic style.

Genuine Mitsubishi EVO OEM Metal head gasket.

By reducing the temperature of the inlet manifold the temperature of the intake air charge is also reduced.

HKS M-Series spark plugs are high performance Iridium plugs designed to provide improved ignition performance, durability and anti-carbon build-up.

Features:
- 0.6mm Iridium Alloy Center Electrode
- Outer Electrode with Platin...

HKS M-Series spark plugs are high performance Iridium plugs designed to provide improved ignition performance, durability and anti-carbon build-up.

Features:
- 0.6mm Iridium Alloy Center Electrode
- Outer Electrode with Platin...

ARP has released Rod Bolts for the Mitsubishi 4B11 engine in the Evolution X ARP Rod Bolts are made of premium grade 8740 chrome moly steel and heat treated to a nominal tensile strength of 200,000 psi.

High performance piston ring set for Cosworth pistons.

High performance piston ring set for Cosworth pistons.

High performance piston ring set for Cosworth pistons.

Increase horsepower, turbo spool and style under the hood of your Evolution! Our designers have released a replacement of the OEM rubber turbo inlet hose for your EVO X. You will see consistent gains in horsepower, throttle response and fuel economy. The turbo inlet hose includes the multilayer...

This is our newest upgrade for the Mitsubishi Evolution X. Made of high durometer polyurethane this will be a great upgrade to stiffen up the engine movement of your Evo as well as help improve shifting.

Agency Power has just released a brand new lower motor mount for your Mitsubishi EVO X.

Agency Power has designed a Mitsubishi Evo X crank pulley for the 4B11 engine.

Agency Power has just release this brand new passenger side motor mount for your Mitsubishi EVO.

Cosworth High Performance Head Gaskets are engineered to seal in power under the most
demanding conditions.

Cosworth High Performance Head Gaskets are engineered to seal in power under the most
demanding conditions.

Help eliminate your engine movement with one of these mounts and cut down on wheel hop as well as firm up your shifting when banging gears.

...

Improve throttle response and Clean up shifting in your Evolution X. Decreases Motor and transmission movement which in turn improves shifting and drive...

This very easy to install piece will allow you to remove you heavy stock battery and mount a lightweight race battery on its side to not only lower the overall weight of the car but also lower the center of gravity....

Building an Evo X to make more power?

The factory head bolts can begin to stretch with higher cylinder pressures and cause a enough space between the block and head for combustion to leak out. Not only are you losing power, you are putting your cooling system and head gasket at...

Engine bearings are one of the most vital components within an engine and are often overlooked when considering high performance upgrades.

The APR main studs are an upgrade over the stock factory bolts that may stretch over time.

Includes a set of ten, M10 ARP2000 main studs, a set of ten, M8 ARP2000 main studs, twenty 8740 chromemoly steel 12 pt nuts and a 1/2 oz. pack of ARP Ultra-Torque fastener assembly lubr...

Add more style to your engine bay with this 3 piece silicone radiator hose kit for the new Mitsubishi EVO X.

Boomba Motor Mounts are designed to gain better traction, improve acceleration and help wth smoother gear shifts.

The Mishimoto Lancer Evolution X fan shroud kit will considerably improve engine cooling functions and the overall performance of your vehicle.

All Mishimoto fan shrouds are significantly lighter than standard fan shrouds. In maintaining the lifetime of your engine, it is ideal to...

AMS designed this upgraded Cam Cap after a number of reports from customers of the OEM piece cracking.

The new single valve spring delivers 15% more pressure across the board than the factory part.

Agency Power has released their new Mitsubishi EVO X fuel rail. This fuel rail is a direct replacement for the factory unit.

This is the ideal upgrade to your stock Evolution X radiator, having a turbo set up produces a great amount of heat, by replacing your current Evolution 10 radiator with a top of the line Mishimoto performance aluminum radiator you will undoubtedly notice a cooler more efficient running engine.

HKS metal head gaskets are engineered to resist severe levels of heat that are generated by high-horsepower and high-boost applications.

All HKS head gaskets are constructed with multiple layers of steel and coated with a special fluorine rubber to provide exceptional seali...

A great way to easily enhance under the hood of your EVO 10.

Direct bolt on, replaces stock unit! No other modifications needed. Easy installation takes 25 minutes and can be done with common hand tools.

This mini-battery kit will enable you to remove another 20lbs out of the rear of you Evo X. This battery has more cranking energy than the factory unit with 1/3 the size.

Cosworth High RPM Valve Springs are wound from the world's finest Japanese Kobe steel and feature dual chamfered ends to reduce wear on seats and retainers.

Engine bearings are one of the most vital components within an engine and are often overlooked when considering high performance upgrades.

Building a Race EVO X?

Includes a full set of intake and exhaust valves.

Building a Race EVO X?

Includes a full set of intake and exhaust valves.

The X Line Mishimoto radiator that provides up to 25% larger core. Built with 3 rows, this radiator is the ideal upgrade to your stock radiator.

Upgraded valve springs and retainers will come in handy if you are building a full race motor!

Manley H-Beam rods are a lower cost alternative to the Turbo Tuff series. The Manley H-Beam rods are extremely high quality yet very economical.

Essential for high performance engine builds, heavy duty head studs reduce cylinder head movement in high boost or high compression engines optimizing cylinder head to block sealing.

Recent trend of automobile equipped with Electric Controlled Throttle Valve replaced from Mechanical Throttle Valve (Cable type).

Brian Crower high performance billet camshafts are CAD designed to optimize torque & horsepower throughout the power band. 272 combo, is geared towards all-out performance.